PRODUCT DESCRIPTION
CreteSafe B-250 is a water-based bituminous emulsion modified with highly elastic polymers. The material is used to protect concrete structures, both above and below the ground level. The applied coating has no seams or joints and protects the treated surface from the penetration of water, salt by 100%, and also protects against any chemical exposure. CreteSafe B-250 r does not lose its properties under the influence of sunlight. It is used in combination with an inorganic salt solution to create an instant hardening coating. The material is elastic. It allows you to avoid the appearance of cracks and ruptures during the settlement of structures during operation. The material is applied with specially designed equipment. The material is water-based, solvent-free, non-toxic and environmentally friendly. When working with CreteSafe B-250, there is no need to use open fire and material heating. The operating temperature range of the coating is from -45 ̊C to +80 C (peak -55 C and +95 C).
SCOPE OF APPLICATION
- monolithic block foundations;
- bearing walls;
- foundation slabs;
- lining of tunnels, concrete pipes;
- parking areas;
- concrete tanks for water and liquid waste;
- cement screeds, ;
- Fixed formwork made of granulated polystyrene
CreteSafe B-250 is easy to apply and provides excellent waterproofing and chemical protection due to the highly flexible, seamless membrane which does not crack or wear. CreteSafe B-250 is not exposed to acids, alkalis, salts and other inorganic chemicals. The waterproofing coating created by CreteSafe B-250 material does not lose its properties for more than 20 years. CreteSafe B-250 is sprayed in combination with an inorganic salt solution to create a waterproofing roofing coating which allows to get a ready-to-use waterproofing coating within seconds. CreteSafe B-250 is an alternative to conventional hot-applied bituminous coatings and solvent-based protective coatings, it is easier to use than ready-made polymer film.
PREPARATION OF THE BASE BEFORE APPLYING THE EMULSION
The base for CreteSafe B-250 shall be clean, dry, and free of substances that prevent adhesion (grease, dust, stains from gasoline and diesel fuel, etc.). Before applying CreteSafe B-250, it is recommended to prime the
surface with a primer from Liquid Rubber line of materials. Without an inorganic salt solution, CreteSafe B-250 can be applied as a primer to any building structure made of bricks, blocks and concrete.
PERFORMANCE OF WORK
Before using CreteSafe B-250, it is necessary to mix it manually, or with a construction mixer at low speed for 3-5 minutes. The CreteSafe B-250 emulsion is applied using HVLP 2000GX sprayer, which has been specially designed for the application of Liquid Rubber materials. The coating becomes dry to the touch in one minute, the full drying process is within 24-48 hours, depending on weather conditions.
CONSUMPTION
Material consumption depends on the thickness of the desired membrane and ranges from 2 to 3.5 kg/m2.
The consumption of CreteSafe B-250 emulsion to get a dry coating layer with 2 mm of thickness is ≈ 2.7 kg/m2.
RECOMMENDATIONS FOR THE PERFORMANCE OF WORK
Work shall be carried out at air temperature from +5 to + 30°C and relative air humidity no more than 80%. The material is a medium alkaline substance. Wear protective clothing, goggles and gloves while working. Wash off fresh dirt with water. Cured material can be removed with white spirit solvent. In case of eye contact, rinse with plenty of water and seek medical advice. When using the material, please, follow current regulations related to construction.
STORAGE
The material shall be stored in undamaged tightly closed packaging in a dry place at a temperature no lower than +5°C. The shelf life is within 12 months from the date of manufacture indicated on the packaging. Unused material may be stored until the end of the shelf life in a container with the lid tightly closed.
WARNING
Keep away from children. Protect from freezing! The emulsion shall not be applied at an ambient temperature below +5°C. An incompletely cured membrane may be damaged if it freezes. Do not apply the material onto wet or frozen surfaces. Avoid contact of the material with any solvents.
When applying this product, please, follow safety guidelines, wear gloves, goggles, and other appropriate protective equipment.
PACKAGING
CreteSafe B-250 is supplied only in industrial packaging:
- 1000 Euro cubes (IBC)
- 220 plastic buckets
PHYSICAL CHARACTERISTICS OF THE EMULSION | |
Appearance | Homogeneous viscous black mastic |
Mass fraction of non-volatile substances (dry residues) | 62-63% |
pH value | 11-12 |
Relative viscosity per viscometer with a nozzle diameter of 4 mm, s | 5 |
COATING CHARACT | ERISTICS |
Nominal tensile strength, MPa | 0.73 |
Tensile elongation, % | 1100 |
Adhesion strength with the base, MPa | 1.28 |
Water absorption by weight within 24 hours, % | 0.1 |
Flexibility at minus 20°C | No cracks have been identified |
Heat resistance at a temperature of + 90C 5h. | No blisters or leaks have been identified |
Waterproofing within72 h at a pressure of 0.001 MPa | In 72 hours, there are no signs of water penetration detected. |
RESISTANCE TO AGGRE | SSIVE MEDIA |
Acidity | |
Nominal tensile strength, MPa | 0.73 |
Reduction of nominal tensile strength, % | NO |
Tensile elongation, % | 1180 |
Tensile elongation reduction, % | NO |
Alkalinity | |
Nominal tensile strength, MPa | 0.75 |
Reduction of nominal tensile strength, % | NO |
Tensile elongation, % | 1170 |
Tensile elongation reduction, % | NO |
Permeability to steam kg/(м• s• Pa) | 0.19•10 -12 |
The manufacturer guarantees the compliance of the material with the specified technical characteristics; however, the manufacturer has no influence on the method and conditions of use of the material and is not responsible for poor performance of work and violations of the technology of work. Please, get yourself familiarized with the Safety Data Sheet for CreteSafe B-250 before using it. For any questions, please contact technical support, or regional representatives.